![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
|||||||
![]() |
||||||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
Fire Research Division
Fire Safety in Passenger Rail Transportation
Overview
Fire safety of passenger trains in the United States has been approached by regulating the flammability of furnishing and finish materials since early in the 20th century. In the past decade advances in technology associated with the development of high-speed trains has led to increasing use of light-weight synthetic materials whose end-use performance may not be well predicted by small-scale tests. Considerable research has been conducted to develop quantitative methods to assess the fire performance of the entire system, starting with modern metrics for the flammability of materials. The Fire Research Division has been involved in research related to passenger train fire safety since the 1970's. The results of these research studies are summarized below. The complete reports are available as Adobe Acrobat PDF files.
From 1975 to 1979, rail transit car fire hazard evaluation reports for the Washington Metropolitan Area Transit Administration (WMATA) and Bay Area Rapid Transit District (BART) systems were published. The WMATA subway car fire evaluation consisted of individual small-scale tests of several interior materials and seven full-scale tests to determine the overall effects of an assembled system as compared to the fire characteristics of the individual components. The intent was to assist WMATA in assessing the potential fire hazard in new Metrorail subway cars. One criterion was that the ignition not spread from the area of origin. While the small-scale test results indicated that the car interior may not be readily ignited by very small ignition sources, the full-scale test results showed that the materials failed to perform in their end-use configuration as would have been predicted. For mock-up tests with urethane foam seat cushions, significant smoke obscuration was evident in approximately 5 minutes. Vinyl/chloroprene seat cushions were seen as less hazardous than an integral skin urethane foam assembly. The BART rail car evaluation included the review of interior and exterior car design, communication system, materials (tests and performance), fire detection and suppression, fire statistics, and scenarios. No tests were conducted. An additional study investigated fire safety guidelines for automated people movers systems. An extensive review of literature related to fire safety of fixed guideway transit systems was included in the report.
- Fire Hazard Evaluation of the Interior of WMATA Metrorail Cars by E. Braun, 1975 (971 KB)
- Fire Hazard Evaluation of BART Vehicles by E. Braun, 1978 (335 KB)
- Fire Safety Guidelines for Vehicles in a Downtown People Mover System by R. Peacock, 1979 (3002 KB)
NIST studied the large-scale burning behavior of materials used for Amtrak passenger rail car interior furnishings. Small-scale cone calorimeter tests, and full-scale furniture calorimeter assembly tests were conducted. The comparison of small-scale flammability and smoke emission test data with real-scale test data showed that the small-scale tests were able to effectively quantify the effect of changes in materials within the same real-scale geometry. However, when the geometry of the full-scale rail coach car test mockup was changed, the chosen small-scale tests failed to predict the effects of the changes. Small-scale seat assemblies, and real-scale mock-up test data were compared. The relative fire performance of these materials (from lowest HRR to highest HRR) was consistent in mockup tests (for a given geometry of the full-scale mockup).
- Fire Tests of Amtrak Passenger Rail Vehicle Interiors by R. Peacock and E. Braun, 1983 (1966 KB)
Beginning in the mid-1990's the U.S. Federal Railroad Administration (FRA) funded NIST to develop a systematic approach to the quantification of fire hazards in passenger trains that could form the basis for regulatory reform. At the time the research began the FRA issued guidelines that were generally utilized by the U.S. rail industry. During the work a major train accident in Silver Spring, Maryland occurred in 1996 that eventually resulted in the FRA guidelines being converted to federal regulations. An extensive literature review documented U.S. and European approaches to passenger train fire safety that rely primarily on individual small-scale test methods to evaluate material fire performance. This was followed by a three-phase research program. Phase I focused on the evaluation of passenger rail car interior furnishing materials using data from existing FRA-cited small-scale test methods and from an alternative test method using the cone calorimeter (ASTM International E-1354) . In Phase II, full-scale tests were conducted of selected interior material component assemblies using a larger scale furniture calorimeter; fire hazard analyses were then conducted for three types of intercity passenger rail cars, using data from both types of tests. Phase III compared the results of Phases I and II of the research program, with a series of full-scale fire tests conducted in an Amtrak coach rail car.
From the fire hazard analyses conducted, conditions in all three passenger rail car designs studied remain tenable sufficiently long enough to allow safe passenger and crew egress for all but the most severe ignition sources. Comparison of times to untenable conditions for a range of fire sizes determined from the full-scale experimental measurements with those calculated by the CFAST fire model showed agreement which averaged approximately 13 %. The range of ignition source strengths indicated that an ignition source size between 25 kW and approximately 200 kW is necessary to promote significant fire spread, which is consistent with the conclusions from earlier research that the ignition source strength of passenger rail car materials is 2 to 10 times greater than typical office furnishings.
- Fire Safety of Passenger Trains: A Review of Current Approaches and of New Concepts by R. Peacock, R. Bukowski, W. Jones, P. Reneke, V. Babrauskas, and J. Brown, 1994 (8117 KB)
- Fire Safety of Passenger Trains. Phase 1: Material Evaluation (Cone Calorimeter) by R. Peacock and E. Braun, 1999 (1940 KB)
- Fire Safety of Passenger Trains. Phase 2: Application of Fire Hazard Analysis Techniques by R. Peacock, P. Reneke, J. Averill, R. Bukowski, and J. Klote, 2002 (7912 KB)
- Fire Safety of Passenger Trains; Phase 3: Evaluation of Fire Hazard Analysis Using Full-Scale Passenger Rail Car Tests by R. Peacock, J. Averill, D. Madrzykowski, D. Stroup, P. Reneke, and R. Bukowski, 2004 (6666 KB)
For further information, contact Richard D. Peacock, richard.peacock@nist.gov, (301) 975-6664, fax: (301) 975-4052
![]() |
Privacy Policy/Security Notice | Disclaimer | FOIA NIST is an agency of the U.S. Commerce Department's Technology Administration. |
![]() |
Date created: 3/12/2001
Last updated: 11/30/2003