[Federal Register: March 28, 2001 (Volume 66, Number 60)]
[Proposed Rules]               
[Page 16884-16893]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr28mr01-17]                         
 
========================================================================
Proposed Rules
                                                Federal Register
________________________________________________________________________
 
This section of the FEDERAL REGISTER contains notices to the public of 
the proposed issuance of rules and regulations. The purpose of these 
notices is to give interested persons an opportunity to participate in 
the rule making prior to the adoption of the final rules.
 
========================================================================
 
 
 
[[Page 16884]]
 
 
 
DEPARTMENT OF HEALTH AND HUMAN SERVICES
 
Food and Drug Administration
 
21 CFR Parts 129 and 165
 
[Docket No. OIN-0126]
 
 
Beverages:  Bottled   Water ; Companion Document to Direct Final Rule
 
AGENCY: Food and Drug Administration, HHS.
 
ACTION: Proposed rule.
 
-----------------------------------------------------------------------
 
SUMMARY: The Food and Drug Administration (FDA) is proposing to amend 
its  bottled   water  quality standard by establishing allowable levels in 
its regulations for three residual disinfectants (chloramine, chlorine, 
and chlorine dioxide) and three types of disinfection byproducts 
(DBP's) (bromate, chlorite, and haloacetic acids (HAA5)). FDA also is 
proposing to revise the existing allowable level for the DBP total 
trihalomethanes (TTHM). Finally, FDA is also proposing to revise, for 
the three residual disinfectants and four types of DBP's only, the 
monitoring requirement for source  water  found in the current good 
manufacturing practice (CGMP) regulations for  bottled   water . As a 
consequence of FDA's amending the quality standard for these residual 
disinfectants and DBP's,  bottled   water  manufacturers would be required 
to monitor their finished  bottled   water  products for these 
disinfectants and DBP's at least once each year under the CGMP 
regulations for  bottled   water .  Bottled   water  manufacturers also would 
be required to monitor for these contaminants at least once each year 
in their source  water , unless the bottlers meet the criteria for the 
source  water  monitoring exemption under the proposed amendment to the 
CGMP regulations. This proposed rule will ensure that the minimum 
quality of  bottled   water , as affected by the above disinfectants and 
DBP's, remains comparable with the quality of public drinking  water  
that meets the Environmental Protection Agency's (EPA's) standards. 
This proposed rule is a companion to the direct final rule published 
elsewhere in this issue of the Federal Register.
 
DATES: Submit written comments by June 11, 2001.
 
ADDRESSES: Submit written comments on the companion proposed rule to 
the Dockets Management Branch (HFA-305), Food and Drug Administration, 
5630 Fishers Lane, rm. 1061, Rockville, MD 20852.
 
FOR FURTHER INFORMATION CONTACT: Lauren Posnick, Center for Food Safety 
and Applied Nutrition (HFS-306), Food and Drug Administration, 200 C 
St. SW., Washington, DC 20204, 202-358-3568.
 
SUPPLEMENTARY INFORMATION:
 
I. Background
 
    This proposed rule is a companion to the direct final rule 
published in the final rules section of this issue of the Federal 
Register. The companion proposed rule and the direct final rule are 
substantively identical. This companion proposed rule will provide the 
procedural framework to finalize the rule in the event the direct final 
rule receives significant adverse comment and is withdrawn. The comment 
period for the companion proposed rule runs concurrently with the 
comment period of the direct final rule. Any comments received under 
the companion proposed rule will be treated as comments regarding the 
direct final rule. FDA is publishing the direct final rule because the 
rule contains noncontroversial changes, and the agency anticipates that 
it will receive no significant adverse comment. A detailed discussion 
of this rule is set forth in the preamble of the direct final rule. If 
no significant adverse comment is received in response to the direct 
final rule, no further action will be taken related to this proposed 
rule. Instead, FDA will publish a confirmation notice, after the 
comment period ends, to confirm the effective date of the direct final 
rule. The confirmation notice will publish no later than July 5, 2001. 
FDA intends the direct final rule to become effective January 1, 2002. 
If FDA receives significant adverse comment, the agency will withdraw 
the direct final rule. FDA will proceed to respond to all of the 
comments received regarding the rule, and, if appropriate, the rule 
will be finalized under this companion proposed rule using notice-and-
comment procedures. The comment period for this companion proposed rule 
runs concurrently with the comment period for the direct final rule. 
Any comments received under this companion proposed rule will also be 
considered as comments regarding the direct final rule.
    On December 16, 1998 (63 FR 69390), EPA published the Stage 1 
Disinfection Byproducts Rule (Stage I DBPR) to address potential public 
health effects from the presence of disinfectants and DBP's in drinking 
 water . This rulemaking finalized a proposed rule that EPA published in 
the Federal Register on July 29, 1994 (59 FR 38668).
    Disinfectants are chemicals, such as chlorine and ozone, that are 
added to drinking  water  to control microbial contamination. Both 
bottlers and public  water  systems may use disinfectants. Public  water  
systems typically add disinfectants to drinking  water  at levels 
sufficient to maintain a disinfectant residual throughout the 
distribution system (i.e., the system of pipes that takes  water  from 
 water  treatment plants to customers). DBP's are chemicals that result 
from the unintentional interaction of the disinfectants with inorganic 
or organic compounds present in the  water  supply. Examples of DBP's 
include chloroform (a byproduct of treatment with chlorine) and bromate 
(a byproduct of ozonation). Both disinfectants and DBP's can have 
adverse health effects (59 FR 38668 at 38679 through 38710).
    National primary drinking  water  regulations (NPDWR's) are 
promulgated by EPA to protect the public health from the adverse 
effects of contaminants in drinking  water . NPDWR's specify maximum 
contaminant levels (MCL's) or treatment techniques for drinking  water  
contaminants. In addition, at the same time that it promulgates 
NPDWR's, EPA publishes maximum contaminant level goals (MCLG's), which 
are not regulatory requirements but rather are nonenforceable health 
goals that are based solely on considerations of protecting the public 
from adverse health effects of drinking  water  contamination. In its 
proposed rule on disinfectants and DBP's (59 FR 38668), EPA also 
introduced the concept of maximum residual disinfectant levels (MRDL's) 
and maximum residual disinfectant level goals (MRDLG's). MRDL's and 
MRDLG's are comparable
 
[[Page 16885]]
 
to MCL's and MCLG's, in that they set contaminant levels and health 
goals, respectively. EPA used the terms MRDL and MRDLG for 
disinfectants, rather than using the terms MCL and MCLG, to reflect the 
fact that disinfectants have beneficial properties (63 FR 69390 at 
69398, December 16, 1998; 59 FR 38668 at 38672, and 38679).
    In the Stage I DBPR (63 FR 69390), EPA published NPDWR's consisting 
of MCL's for the DBP's bromate, chlorite, HAA5, and TTHM. EPA also 
published MRDL's for the chlorine-based disinfectants chlorine, 
chloramine, and chlorine dioxide. Finally, EPA published MCLG's and 
MRDLG's for these contaminants, as well as approved methods of testing 
for these contaminants.
    Under section 410 of the Federal Food, Drug, and Cosmetic Act (the 
act) (21 U.S.C. 349), not later than 180 days before the effective date 
of an NPDWR promulgated by EPA for a contaminant under section 1412 of 
the Safe Drinking  Water  Act (SDWA) (42 U.S.C. 300g-l)\1\, FDA is 
required to promulgate a standard of quality regulation for that 
contaminant in  bottled   water  or make a finding that such a regulation 
is not necessary to protect the public health because the contaminant 
is contained in  water  in public  water  systems but not in  water  used for 
 bottled  drinking  water . The effective date for any such standard of 
quality regulation is to be the same as the effective date of the 
NPDWR. In addition, section 410(b)(2) of the act provides that a 
quality standard regulation issued by FDA shall include monitoring 
requirements that the agency determines to be appropriate for  bottled  
 water . Further, section 410(b)(3) of the act requires a quality 
standard regulation for a contaminant in  bottled   water  to be no less 
stringent than EPA's MCL and no less protective of the public health 
than EPA's treatment technique requirements for the same contaminant.
---------------------------------------------------------------------------
 
    \1\FDA considers EPA's compliance date for subpart H public 
 water  systems (systems using surface  water  or ground  water  under the 
direct influence of surface  water ) that serve a population of 10,000 
or more to be the effective date for purposes of section 410 of the 
act. The compliance date was set at December 16, 2001, in the Stage 
I DBPR (63 FR 69390) and updated in a subsequent rule to January 1, 
2002 (65 FR 20303, April 14, 2000).
---------------------------------------------------------------------------
 
II. Additional Information
 
    For additional information see the corresponding direct final rule 
published elsewhere in this issue of the Federal Register. All persons 
who wish to submit comments should review the detailed rationale for 
these amendments set out in the preamble discussion of the direct final 
rule.
    If FDA receives any significant adverse comments regarding this 
rule, FDA will publish a document withdrawing the direct final rule and 
will proceed to respond to the comments under this companion proposed 
rule using usual notice and comment procedures.
    A significant adverse comment is one that explains why the rule 
would be inappropriate, including challenges to the rule's underlying 
premise or approach, or why it would be ineffective or unacceptable 
without a change. A comment recommending a rule change that is in 
addition to the rule will not be considered a significant adverse 
comment, unless the comment states why this rule would be ineffective 
without the additional change. In addition, if a significant adverse 
comment applies to part of a rule and that part can be severed from the 
remainder of the rule, FDA may adopt as final those parts of the rule 
that are not the subject of a significant adverse comment.
 
III. EPA Standards
 
    The SDWA, as amended in 1996, requires EPA to publish an NPDWR that 
specifies either an MCL or a treatment technique requirement for 
contaminants that may ``have an adverse effect on the health of 
persons,'' are ``known to occur or [have] a substantial likelihood [of 
occurring] in public  water  systems with a frequency and at levels of 
public health concern,'' and for which ``regulation * * * presents a 
meaningful opportunity for health risk reduction for persons served by 
public  water  systems'' (SDWA Section 1412(b)(1)(A)). The SDWA (Section 
300g-1(a)(3)) also requires that EPA promulgate MCLG's at the time that 
it promulgates NPDWR's. MCLG's are nonenforceable health goals that are 
based solely on considerations of protecting the public from the 
adverse health effects of contaminants, and not on other 
considerations, such as potential costs of regulating contaminants and 
potential technical difficulties of achieving the health goals (59 FR 
38668 at 38671). EPA sets MCL's, the enforceable contaminant levels, as 
close as feasible to the nonenforceable MCLG's.
    In its proposed rule on disinfectants and DBP's (59 FR 38668), EPA 
also introduced the concept of MRDL's and MRDLG's. MRDL's and MRDLG's 
are comparable to MCL's and MCLG's, in that they set contaminant levels 
and health goals. EPA used the terms MRDL and MRDLG for disinfectants, 
rather than using the terms MCL and MCLG, to reflect the fact that 
disinfectants have beneficial properties and are intentionally added to 
drinking  water  to kill disease-causing organisms (63 FR 69390 at 69398; 
59 FR 38668 at 38672, and 38679).
    In the Stage I DBPR (63 FR 69390 at 69396), EPA established an MCL 
of 0.060 milligram per liter (mg/L) for the total of the five 
haloacetic acids that make up HAA5 (i.e., mono-, di-, and 
trichloroacetic acid, and mono- and dibromoacetic acid). EPA also 
reduced the existing MCL for TTHM from 0.10 mg/L to 0.080 mg/L (63 FR 
69390 at 69396). EPA also established MCL's for two inorganic DBP's: 
0.010 mg/L for bromate and 1.0 mg/L for chlorite (63 FR 69390 at 
69396). Finally, EPA established MRDL's for three disinfectants: 4.0 
mg/L (as Cl2) for chlorine, 4.0 mg/L (as Cl2) for 
chloramine, and 0.8 mg/L (as ClO2) for chlorine dioxide (63 
FR 69390 at 69396).
 
IV. FDA Standards
 
A. The Agency's Approach to the  Bottled   Water  Quality Standards 
Established Under Section 410 of the Act.
 
    Under section 401 of the act (21 U.S.C. 341), the agency may 
promulgate a regulation establishing a standard of quality for a food 
under its common or usual name, when in the judgment of the Secretary 
of Health and Human Services such action will promote honesty and fair 
dealing in the interest of consumers. On November 26, 1973 (38 FR 
32558), FDA established a quality standard for  bottled   water  that is 
set forth in Sec. 165.110 (21 CFR 165.110).
    Producers of  bottled   water  are responsible for assuring, through 
appropriate manufacturing techniques and sufficient quality control 
procedures, that all  bottled   water  products introduced or delivered for 
introduction into interstate commerce comply with the quality standard 
(Sec. 165.110(b)).  Bottled   water  that is of a quality that is below the 
prescribed standard is required by Sec. 165.110(c) to be labeled with a 
statement of substandard quality. Moreover, any  bottled   water  
containing a substance at a level that causes the food to be 
adulterated under section 402(a)(1) of the act (21 U.S.C. 342(a)(1)) is 
subject to regulatory action, even if the  bottled   water  bears a label 
statement of substandard quality.
    FDA has traditionally fulfilled its obligation under section 410 of 
the act to respond to EPA's issuance of NPDWR's by amending the quality 
standard regulations for  bottled   water  introduced or delivered for 
introduction
 
[[Page 16886]]
 
into interstate commerce to maintain compatibility with EPA's drinking 
 water  regulations. In general, FDA believes that, with few exceptions, 
EPA standards for contaminants in drinking  water  are appropriate as 
allowable levels for contaminants in the quality standard for  bottled  
 water  when  bottled   water  may be expected to contain the same 
contaminants.
    FDA generally has not duplicated the efforts of EPA in judging the 
adequacy of MCL's or treatment techniques in NPDWR's for contaminants 
when determining their applicability to  bottled   water  in order to 
protect the public health. FDA believes that, in general, it would be 
redundant for FDA to reevaluate the drinking  water  standards prescribed 
by EPA. Further, because  bottled   water  is increasingly used in some 
households as a replacement for tap  water , consumption patterns 
considered by EPA for tap  water  can be used as an estimate for the 
maximum expected consumption of  bottled   water  by some individuals. 
Therefore, FDA's view is that generally in cases where  bottled   water  is 
subject to the same contaminants as tap  water , FDA should establish 
standard of quality levels in  bottled   water  at the same levels that EPA 
establishes as MCL's for such contaminants in tap  water .
    In its proposed rule on disinfectants and DBP's (59 FR 38668), EPA 
introduced the term MRDL. As explained in section III of this document, 
EPA used this term when it first proposed enforceable disinfectant 
levels (MRDL's) to reflect the fact that disinfectants have beneficial 
properties. However, disinfectants may have adverse health effects (59 
FR 38668 at 38679 through 38694) and they may be expected to be in some 
source waters used for  bottled   water . Therefore, FDA is proposing that 
disinfectants should be treated as contaminants when FDA establishes a 
standard of quality for  bottled   water  in response to EPA's issuance of 
NPDWR's for drinking  water .
 
B. Quality Standard for Disinfectants and DBP's
 
    The quality standard for  bottled   water , as set forth in 
Sec. 165.110(b)(4)(i)(A), prescribes that  bottled   water  shall not 
contain TTHM in excess of 0.10 mg/L. It does not, however, prescribe 
allowable levels for bromate, chlorite, HAA5, chloramine, chlorine, or 
chlorine dioxide in  bottled   water .
    FDA has evaluated the MRDL's for chloramine, chlorine, and chlorine 
dioxide and the MCL's for bromate, chlorite, HAA5, and TTHM that EPA 
has established for drinking  water . FDA has tenatively concluded that 
EPA's MRDL's and MCL's for these contaminants, as standard of quality 
levels for  bottled   water , are adequate for the protection of the public 
health. Certain waters used for  bottled  drinking  water  may be expected 
to contain these contaminants; thus, FDA believes that adopting 
allowable levels for these contaminants will ensure that the quality of 
 bottled   water  is comparable to the quality of public drinking  water  
that meets EPA standards.
    Therefore, FDA is proposing to establish in a new paragraph 
(b)(4)(iii)(H) in Sec. 165.110, allowable levels for the following 
disinfectants and DBP's: chloramine at 4.0 mg/L (as Cl2), 
chlorine at 4.0 mg/L (as Cl2), chlorine dioxide at 0.8 mg/L 
(as ClO2), bromate at 0.010 mg/L, chlorite at 1.0 mg/L, HAA5 
at 0.060 mg/L, and TTHM at 0.080 mg/L. FDA is proposing to remove the 
existing entry for TTHM in Sec. 165.110(b)(4)(i)(A).
 
C. Analytical Methods
 
    In the Stage 1 DBPR that established MCL's for bromate, chlorite, 
HAA5, and TTHM and MRDL's for chlorine, chloramine, and chlorine 
dioxide, EPA stipulated that analyses for determining compliance with 
the MCL's and MRDL's shall be performed by approved analytical methods 
(63 FR 69390 at 69466). EPA has approved one method for bromate 
monitoring, two methods for monthly chlorite monitoring, three methods 
for HAA5 monitoring, three methods for TTHM monitoring, six methods for 
chloramine monitoring, seven methods for chlorine monitoring, and two 
methods for chlorine dioxide monitoring. Therefore, in a new paragraph 
(b)(4)(iii)(I) in Sec. 165.110, FDA is proposing to incorporate by 
reference the 24 analytical methods cited by EPA (63 FR 69390 at 69417) 
for determining the levels of these contaminants in  bottled   water .
 
D. Monitoring Provisions of CGMP Regulations for  Bottled   Water 
 
    FDA has established CGMP regulations for  bottled   water  in part 129 
(21 CFR part 129). Under Sec. 129.35(a)(3)(i), source  water  must be 
analyzed by the plant as often as necessary, but at least annually for 
chemical contaminants. Further, to ensure that a plant's production 
complies with applicable standards, Sec. 129.80(g)(2) requires analysis 
by the plant, at least annually, of a representative sample from a 
batch or segment of a continuous production run for each type of 
 bottled  drinking  water  produced during a day's production. The CGMP 
regulation in Sec. 129.80(a) also requires sampling and analysis, as 
often as necessary, of product  water  taken after processing but before 
bottling, to assure uniformity and effectiveness of the processes 
performed by the plant.
    Disinfectants and DBP's are special types of contaminants in that 
they result from the deliberate addition of disinfectants to  water  to 
control microbial contamination. Since public  water  systems add 
disinfectants to  water , FDA expects that source  water  from public  water  
systems will contain disinfectants and DBP's. Therefore, FDA is 
proposing to require bottlers who obtain their source  water  from public 
 water  systems to test that  water , as specified in Sec. 129.35(a)(3)(i), 
for the disinfectants chloramine, chlorine, and chlorine dioxide, and 
the DBP's bromate, chlorite, HAA5, and TTHM, unless they meet the 
requirements contained in Sec. 129.35(a)(4)(i). FDA believes that, in 
some cases, bottlers disinfect source  water  that is not from public 
 water  systems (e.g., prior to bulk transportation of that source  water  
to the bottling plant). Such source  water  would contain residual 
disinfectants and also may contain DBP's. Therefore, FDA is proposing 
to add a new paragraph (a)(4)(iii) in Sec. 129.35, stating that firms 
that do not use a public  water  system as the source of their  water  and 
whose source  water  has not been treated with a chlorine-based 
disinfectant or ozone do not have to test their source  water  for the 
residual disinfectants and DBP's listed in Sec. 165.110(b)(4)(iii)(H). 
FDA is proposing that firms that do not use a public  water  system as 
the source of their  water  but whose source  water  has been treated with 
a chlorine-based disinfectant or ozone must test their source  water  for 
the residual disinfectants and the DBP's listed in 
Sec. 165.110(b)(4)(iii)(H) that are likely to result from such 
treatment. Treatment of  water  with ozone is expected to produce the 
disinfection byproducts (or components of the disinfection byproducts) 
bromate, HAA5, and TTHM. Treatment of  water  with chlorine or chloramine 
is expected to produce the disinfection byproducts (or components of 
the disinfection byproducts) HAA5 and TTHM.
    However, if the proposed changes to the quality standard 
regulations are finalized as proposed, all bottlers, whether or not 
they obtain their source  water  from public or nonpublic drinking  water  
sources and whether or not they treat their  water  with chlorine, 
chloramine, chlorine dioxide, or ozone, would be required to test for 
the residual disinfectants chloramine,
 
[[Page 16887]]
 
chlorine, and chlorine dioxide and the DBP's bromate, chlorite, HAA5, 
and TTHM in their finished  bottled   water  products under 
Sec. 129.80(g)(2) in the CGMP regulations for  bottled   water . FDA 
believes that the potential for the presence of disinfectants and DBP's 
in the finished  bottled   water  product exists. For example, some 
manufacturers may treat their  water  with a disinfectant during 
processing. Further, contamination of the  bottled   water  product with 
disinfectants may occur during the manufacturing process, for example, 
if poor manufacturing practices are followed, such as inadequate 
rinsing of equipment that has undergone sanitizing operations. Section 
129.80(d) in the CGMP regulations for  bottled   water  allows for the use 
of disinfectants (ozone and chlorine-based disinfectants) for 
sanitizing operations.
    Further,  bottled   water  would have to comply with the sampling and 
testing requirements for disinfectants and DBP's under 
Sec. 129.80(g)(2). In addition,  bottled   water  would have to comply with 
the allowable levels for the disinfectants and DBP's in the quality 
standard for  bottled   water  (Sec. 165.110 (b)) unless the label bears a 
statement of substandard quality under Sec.  165.110(c). As stated in 
Sec.  165.110(d),  bottled   water  is deemed to be adulterated if it 
contains a substance at a level considered injurious to health under 
section 402(a)(1) of the act.
 
V. Environmental Impact
 
    The agency has determined under 21 CFR 25.32(a) and 25.30(j) that 
this action is of a type that does not individually or cumulatively 
have a significant effect on the human environment. Therefore, neither 
an environmental assessment nor an environmental impact statement is 
required.
 
VI. Economic Impact
 
A. Initial Regulatory Impact Analysis
 
    FDA has examined the economic implications of this companion 
proposed rule as required by Executive Order 12866. Executive Order 
12866 directs agencies to assess all costs and benefits of available 
regulatory alternatives and, when regulation is necessary, to select 
regulatory approaches that maximize net benefits (including potential 
economic, environmental, public health and safety, and other 
advantages; distributive impacts; and equity). Executive Order 12866 
classifies a rule as significant if it meets any one of a number of 
specified conditions, including: Having an annual effect on the economy 
of $100 million, adversely affecting a sector of the economy in a 
material way, adversely affecting competition, or adversely affecting 
jobs. A regulation is also considered a significant regulatory action 
if it raises novel legal or policy issues. FDA has determined that this 
companion proposed rule is not a significant regulatory action as 
defined by Executive Order 12866.
1. The Need for Regulation
    In the Federal Register of December 16, 1998 (63 FR 69390), EPA 
published a final rule promulgating NPDWR's consisting of MRDL's for 
the disinfectants chlorine, chloramine, and chlorine dioxide; and MCL's 
for the DBP's bromate, chlorite, HAA5, and TTHM. Under section 410 of 
the act, when EPA promulgates a regulation establishing an MCL for a 
contaminant in public drinking  water , FDA is required to issue a 
standard of quality regulation for that contaminant in  bottled   water  or 
make a finding that such a regulation is not necessary to protect the 
public health. FDA's standard of quality regulations must also include 
appropriate monitoring requirements. If FDA does not issue a standard 
of quality regulation by 180 days before the effective date of EPA's 
NPDWR's, the NPDWR's become applicable to  bottled   water .
    In the following analysis, FDA finds that issuing standard of 
quality regulations and monitoring requirements for these residual 
disinfectants and DBP's under FDA  bottled   water  CGMP regulations has 
the highest net benefits. FDA's testing requirements are less costly 
than the testing requirements under our assumptions of how EPA NPDWR's 
would apply to  bottled   water , with the same health benefits, and the 
health benefits of testing for these contaminants outweigh the cost.
2. Cost of the Regulation
    If FDA does not establish a regulation for quality standards for 
these residual disinfectants and DBP's,  bottled   water  producers would 
be subject to NPDWR testing and monitoring requirements for these 
contaminants. Therefore, we consider this possibility the baseline for 
the purposes of this analysis. Also, we assume that the regulatory 
options we consider will have no organoleptic effect on the final 
 bottled   water  product, and thus no impact on sales due to product 
quality, so the cost of the regulation will be limited to the direct 
cost of testing, recordkeeping, and possible disinfection technology 
investment.
     Bottled   water  producers market their products based on meeting 
government safety testing requirements. However, any change in sales 
resulting from successful marketing either transfers revenue from one 
producer to another with no net loss to society, or causes increased 
sales of  bottled   water , which would mitigate the cost of this 
regulatory effort.
    FDA considers three options for this analysis:
    (1) FDA does not establish residual disinfectant and DBP quality 
standard regulations or make a finding that they are not necessary to 
protect the public health because these contaminants are not used in 
 water  used for  bottled  drinking  water .  Bottled   water  producers would be 
subject to the requirements set forth in the NPDWR's for these 
contaminants.
    (2) FDA establishes residual disinfectant and DBP quality standard 
regulations. For these contaminants,  bottled   water  producers would be 
subject to allowable levels in Sec. 165.110 and CGMP monitoring 
requirements in part 129, as modified in this companion proposed rule.
    (3)  Bottled   water  producers are not subject to either FDA quality 
standard regulations or EPA NPDWR's for these residual disinfectants 
and DBP's.
    Regarding option 3, because it is not the case that these 
contaminants are contained in  water  used in public drinking  water  
sytems but not in  water  used for  bottled  drinking  water , section 
410(b)(1) of the Federal Food, Drug, and Cosmetic Act (the act) does 
not permit this option. The act specifies two alternatives: 
``promulgate a standard of quality regulation under this subsection,'' 
or find that ``such a regulation is not necessary to protect the public 
health because the contaminant is contained in  water  in public  water  
systems * * * but not in  water  used for  bottled  drinking  water .''
    However, the Office of Management and Budget (OMB) cost-benefit 
analysis guidelines recommend discussing statutory requirements that 
affect the selection of regulatory approaches. These guidelines also 
recommend analyzing the opportunity cost of legal constraints that may 
prevent the selection of the regulatory action that best satisfies the 
philosophy and principles of Executive Order 12866. Our analysis finds 
that option 3 does not have the highest net benefits, therefore, even 
if option 3 were permissible, the statute does not preclude the option 
with the highest net benefits.
    a. Testing Costs. Option 3 is the least cost option. If producers 
are not subject
 
[[Page 16888]]
 
to any disinfectant residual and DBP regulations,  bottled   water  firms 
incur no additional costs. Firms already test for TTHM under the CGMP 
regulations, so the new lower bound of the TTHM test should cause only 
a small increase in cost per plant. However, the TTHM frequency 
differences still affect the choice between options 1 and 2, so we 
include TTHM testing in the analysis.
    We assume the following testing frequency and requirements under 
option 1. This option considers the cost if  bottled   water  facilities 
were subject to NPDWR's by interpreting how such requirements may apply 
to  bottled   water  facilities. EPA bases testing frequencies for public 
 water  systems on the size of the population served by the treatment 
plant. Since  bottled   water  plants do not fall into the size and type 
categories established in the 1998 Stage 1 DBPR regulations, for the 
purposes of this analysis, we assume that all  bottled   water  facilities 
would be regulated as if they were a small ground  water  treatment 
system. This is the smallest category identified in the 1998 Stage 1 
DBPR analysis.
    EPA regulations also provide two testing process exemptions. If a 
public  water  system does not use ozone for oxidation or disinfection, 
then EPA does not require a bromate test; and if a public  water  system 
does not use chlorine dioxide for oxidation or disinfection, then EPA 
requires neither a chlorine dioxide nor a chlorite test. All plants 
have to test for HAA5, TTHM, chlorine, and chloramine regardless of 
disinfection method.
    For this analysis, the  bottled   water  industry would be subject to 
the following monitoring:
    i. TTHM and HAA5: One test per plant per year, decreasing to one 
test per 3 years in the event of 1 or 2 years of very low levels of 
both TTHM and HAA5.
    ii. Chlorite: A three-sample set per month only for plants using 
chlorine dioxide as a disinfectant. Reduced to a three-sample set per 
quarter if low levels of chlorites found in routine monitoring in a 1-
year period.
    iii. Bromate: One test per month only for plants using ozone for 
oxidation or disinfection. Reduced to one test per quarter if average 
 water  bromide is low, based on 1-year average of monthly samples.
    iv. Chlorine and Chloramine: One test per plant per month. 
Monitoring may not be reduced.
    v. Chlorine Dioxide: One test per day, at the distribution system 
entrance, only for plants using chlorine dioxide as a disinfectant. 
Monitoring may not be reduced.
    Because few  bottled   water  facilities use chlorine dioxide for 
disinfection, we assume that they all will qualify for the chlorite 
testing exemption. For the HAA5 and TTHM frequency requirements, we 
assume that one-third of the plants will qualify for the frequency 
reductions after 1 year, one-third will qualify for the reductions 
after 2 years, and one-third will continue to have to test once yearly. 
Finally, we assume that no  bottled   water  facility will qualify for the 
bromate testing exemption, but that half of the plants will qualify for 
lower frequency testing under option 1.
    For option 2, under 21 CFR Sec. 129.35(a)(3),  bottled   water  
producers are required to test their source  water  for contaminants at 
least once per year unless exempted from such testing under 
Sec. 129.35(a)(4). For example,  bottled   water  facilities that use a 
public  water  source already subject to EPA regulations may substitute 
public  water  system testing results for source  water  testing. We assume 
that no facilities that use a public  water  source will need to test 
their source  water  for residual disinfectants and the DBP's likely to 
result from such treatment.  Bottled   water  manufacturers that do not use 
a public  water  system as the source of their  water  and whose source 
 water  has not been treated with a chlorine-based disinfectant or ozone 
do not have to test their source  water  for these disinfectants and the 
DBP's. Manufacturers that do not use a public  water  system as the 
source of their  water  but whose source  water  has been treated with a 
chlorine-based disinfectant or ozone must test their source  water  for 
the residual disinfectants and the DBP's likely to result from such 
treatment. For example, some source  water  may be disinfected if it is 
transported across large distances prior to entering the  bottled   water  
plant. We assume in this analysis (explained below) that 75 percent of 
 bottled   water  producers use nonpublic sources. Of these, we assume that 
one-third of  bottled   water  producers using nonpublic  water  will need to 
test their source  water . All  bottled   water  producers are required to 
test their final  bottled   water  product for contaminants at least once 
per year under Sec.  129.80(g)(2).
    Table 1 of this document contains the required annual testing 
frequencies for source and final product  water  for the four types of 
DBP's and three disinfectants under options 1 and 2. For this table, we 
split option 2 into 2a and 2b, referring to whether or not the facility 
uses a public  water  source. This table is for ``year 1'' testing; under 
our assumptions no firm has yet qualified for less frequent testing 
requirements under option 1. We assume that facilities will perform 
separate tests for free chlorine and combined chlorine (which detects 
chloramine) and that all facilities use ozone for oxidation or 
disinfection. Under option 2a, all facilities must perform at least one 
final product test annually, and 25 percent (one-third of the 75 
percent of the facilities using a nonpublic  water  source) of facilities 
must perform an annual source  water  test, for an average of 1.25 tests 
per facility.
 
                                 Table 1.--Annual Average Plant Testing Frequency
----------------------------------------------------------------------------------------------------------------
                                                                            Option 2a  CGMP     Option 2  CGMP
                                                       Option 1  NPDWR's   Regulations Apply   Regulations Apply
                        Test                                 Apply         (Nonpublic Source    (Public Source
                                                                                 Water )               Water )
----------------------------------------------------------------------------------------------------------------
Bromate.............................................                  12                1.25                   1
Chlorite............................................                   0                1.25                   1
TTHM................................................                   1                1.25                   1
Chorine.............................................                  12                1.25                   1
Chlorine Dioxide....................................                   0                1.25                   1
----------------------------------------------------------------------------------------------------------------
 
    The cost estimates in table 2 of this document include labor, and 
are the same testing costs EPA used for the 1998 Stage 1 DBPR impact 
analysis (Ref. 1). FDA also collected other testing cost estimates 
(Ref. 2); the EPA testing costs generally are in the high end of the 
range of the estimates we collected. FDA considers EPA's cost estimates 
reliable
 
[[Page 16889]]
 
for this analysis. FDA believes it likely that a  bottled   water  plant 
would be able to test for these substances at a cost close to this 
range. However, we do not define ``likely'' in any statistical sense. 
We examine the sensitivity of our final results to sample testing cost 
estimates.
 
                                        Table 2.--Estimated Cost per Test
----------------------------------------------------------------------------------------------------------------
                                                Test                                                   Cost ($)
----------------------------------------------------------------------------------------------------------------
Bromate............................................................................................          100
Chlorite...........................................................................................          125
TTHM...............................................................................................          100
HAA5...............................................................................................          200
Chlorine...........................................................................................           20
Chloramine.........................................................................................           20
Chlorine Dioxide...................................................................................           20
----------------------------------------------------------------------------------------------------------------
 
    Table 3 of this document presents annual testing costs. Both option 
2a and 2b cost estimates are considerably lower than option 1 (year 1) 
estimates for a typical  bottled   water  plant, due to the less frequent 
required testing for bromate, chlorine, and chloramine.
 
                                  Table 3. Annual Plant Testing Costs (dollars)
----------------------------------------------------------------------------------------------------------------
                                                                          Option 2a  CGMP       Option 2  CGMP
                                                    Option 1  NPDWR's    Regulations Apply     Regulations Apply
                       Test                               Apply          (Nonpublic Source      (Public Source
                                                                                Water )                Water )
----------------------------------------------------------------------------------------------------------------
Bromate..........................................               1,200                 125                    100
Chlorite.........................................                   0                 156.25                 125
TTHM.............................................                 100                 125                    100
HAA5.............................................                 200                 250                    200
Chloramine.......................................                 240                  25                     20
Chlorine Dioxide.................................                   0                  25                     20
                                                  --------------------------------------------------------------
Total............................................               1,980                 731.25                 585
----------------------------------------------------------------------------------------------------------------
 
    Table 4 of this document applies these totals and assumptions to 
the structure of the  bottled   water  industry. We also recombine options 
2a and 2b in this table. Approximately 1,550 plants produce  bottled  
 water  (63 FR 25764, May 11, 1998). According to another database search 
conducted for this analysis, the industry contains only 914 plants that 
would be subject to these rules, but the current count may not include 
 bottled   water  services to business. Because of this uncertainty, we 
estimate totals for both 914 and 1,550 plants. This affects neither the 
relative ranking of options nor the sensitivity analysis.
    About 25 percent of  bottled   water  products sold are produced by 
facilities that use public source  water . Based on this, FDA assumes 
that 25 percent of  bottled   water  plants use public source  water , and 
that 75 percent use nonpublic sources (mostly ground  water .) For ease 
of computation, table 4 of this document also assumes an equal 
distribution of the once per 3-year cost across later years, so one-
third of the TTHM and HAA5 cost is incurred in any one year for plants 
meeting the less frequent testing requirements under option 1.
 
                       Table 4--Total Cost to Industry (in dollars, assuming 1,550 Plants)
----------------------------------------------------------------------------------------------------------------
                            Year                                  2002         2003         2004         2005
----------------------------------------------------------------------------------------------------------------
Option 2 (a and b)..........................................    1,076,766    1,076,766    1,076,766    1,076,766
Option 1....................................................    3,069,000    2,268,167    2,164,833    2,164,833
----------------------------------------------------------------------------------------------------------------
 
    Assuming a 7 percent discount rate and no relative testing cost 
increases, the present (year 2001) value costs of the testing regimes 
are $18,787,984 (914 plants) to $31,861,461 (1,550 plants) under option 
1 and $9,070,634 (914 plants) to $15,382,366 (1,550 plants) under 
option 2.
    FDA ran a rough sensitivity analysis to determine how the range of 
testing costs, exemptions, and frequency assumptions affected the 
relative cost of options 1 and 2. This is a break-even analysis, which 
identifies how much the costs or assumptions would have to change in 
order to alter our conclusions.
    (1) Testing costs; the major components of the higher option 1 cost 
are bromate, chlorine, and chloramine testing requirements. Even if 
bromate testing cost dropped to zero, option 1 cost would still be 
higher than option 2. If chorine and chloramine testing costs dropped 
to zero, and the cost of testing a  water  sample for bromate dropped 
from $100 to $52 (or if only 52 percent of  bottled   water  plants have to 
test for bromate), the cost of options 1 and 2 would be roughly the 
same. This is in the range of the lowest bromate testing cost estimates 
collected by FDA (Ref. 2). TTHM and HAA5 testing costs do not have a 
significant impact on the relative cost of the options.
    (2) Frequency and requirement exemptions; even if all  bottled   water  
plants qualified for less frequent bromate, TTHM, and HAA5 testing,
 
[[Page 16890]]
 
option 1 costs would still be higher than option 2 costs.
    (3) Discount rate; since option 2 costs, under the original 
assumptions, were lower for every year, the option ranking is not 
affected by the choice of the discount rate.
    FDA concludes that under the most likely assumptions and in a wide 
range around those assumptions, testing costs under option 1 exceed 
those under option 2.
    b. Recordkeeping costs.  Bottled   water  producers already must follow 
FDA CGMP requirements for other contaminants, so option two 
recordkeeping requirements may be lower in cost than option 1. Firms 
have sufficient experience with recordkeeping, so we believe that any 
cost differences are minimal.
    c. Residual disinfectants and DBP control costs. The 1998 Stage I 
DBPR impact analysis estimated costs for public  water  systems to come 
into compliance if a test found unacceptable residual disinfectant or 
DBP levels. However,  bottled   water  producers differ from public  water  
suppliers in two ways. First, we assume one-fourth of  bottled   water  
producers use source  water  already subject to EPA regulations. For the 
purposes of this analysis, we assume they will not have to adopt any 
costly technology to come into compliance. Second, almost all producers 
who do not use public  water  systems for their source  water  use ground 
 water . In the 1998 Stage I DBPR analysis, EPA estimated that only 12 
percent of small ground  water  facilities will have to adopt new 
disinfection technology in order to avoid excessive residual 
disinfectants or DBP's. FDA considers this a high estimate of the 
number of  bottled   water  plants that may need to adopt new technology, 
since these plants do not use as many different types of disinfectants. 
Therefore, at most only 9 percent (0.75 x 0.12) of  bottled   water  plants 
may have to adopt new technology. FDA cannot discriminate between the 
EPA and FDA testing regimes under options 1 and 2 in terms of the 
degree to which they will require new disinfection technology in 
 bottled   water  plants. Once again, no standards will guarantee that 
producers will not have to invest in new compliance technology, so 
option 3 would have the lowest cost.
3. Benefits of the Regulation
    In this case, FDA assumes that both option 1 and option 2 
adequately protect the health of the public. FDA cannot discriminate 
between options 1 and 2 in terms of their ability to guarantee the 
absence of residual disinfectants and DBP's in  bottled   water . Option 3 
is the lowest cost, but in the 1998 Stage 1 DBPR analysis, EPA 
concluded that testing for these substances in  water  destined for human 
consumption has net positive benefits (63 FR 69390, December 16, 1998). 
 Water  used by  bottled   water  producers, from both public and nonpublic 
sources, may need some manner of disinfection, so we believe the 
economic argument from the Stage 1 DBPR analysis applies equally well 
to  bottled   water . We do not estimate the number of illnesses avoided 
under these different testing options.
4. Net Benefits
    Option 2 has lower testing costs and may have lower recordkeeping 
costs than option 1, and protects the health of the public at least as 
well as option 1. Option 2 also has higher net benefits than option 3, 
since the Stage 1 DBPR conclusion that testing for these substances has 
net positive benefits applies equally well to  bottled   water . Therefore, 
option 2, where FDA issues standard of quality regulations for these 
residual disinfectants and DBP's under part 165 and where the 
monitoring requirements in part 129 apply, has the highest net 
benefits.
 
B. Initial Small Entity Analysis
 
    FDA has examined the economic implications of this companion 
proposed rule as required by the Regulatory Flexibility Act (5 U.S.C. 
601-612). If a rule has a significant economic impact on a substantial 
number of small entities, the Regulatory Flexibility Act requires 
agencies to analyze regulatory options that would lessen the economic 
effect of the rule on small entities. FDA finds that this proposed rule 
would have a significant economic impact on a substantial number of 
small entities.
    This proposed rule would have an impact on small entities, but that 
impact would not be large. In addition, option 2 in the impact analysis 
is more flexible and has a smaller testing frequency burden than the 
NPDWR requirements for drinking  water  under option 1, therefore 
lowering the impact of this rule on small businesses while still 
protecting the public health. FDA also believes that adopting residual 
disinfectant and DBP standards yields net positive benefits regardless 
of the size of the  bottled   water  facility, so option 2 in the impact 
analysis is more appropriate than option 3 for small businesses.
    FDA also believes that the flexibility allowed in source testing 
requirements under option 2 in the impact analysis is the maximum 
amount of flexibility possible in this proposed regulation. FDA is not 
proposing exemptions for final product testing since there is a need to 
test for these disinfectant residuals and DBP's:  Bottled   water  
producers use these disinfectants, residual disinfectants and DBP's may 
be present in both public and nonpublic source  water , and disinfectants 
may be used for equipment or other sanitation in any  bottled   water  
plant under CGMP regulations.
    According to the latest database search across the  bottled   water  
industry mentioned above, approximately 72 percent of firms qualify as 
small by Small Business Administration (SBA) standards. Assuming the 
same exemptions and frequency requirements, the yearly average cost per 
plant for both small and large entities is between $585 (public source) 
and $731 (nonpublic source) for firms under the FDA requirements in 
option 2 in the impact analysis, and between $1,397 (year 3) and $1,980 
(year 1) for the NPDWR requirements in option 1. We assume that almost 
all small entities in the  bottled   water  industry are single plant 
firms. Although FDA does consider the option 2 higher cost of $731 per 
plant per year a significant impact for small firms, this number 
represents 0.13 percent of the $580,000 annual revenue of the median 
small  bottled   water  firm.
    C. Unfunded Mandate
    The Unfunded Mandates Reform Act of 1995 (Public Law 104-4), 
requiring cost-benefit and other analyses, in section 1531 (a) defines 
a significant rule as ``a Federal mandate that may result in the 
expenditure by State, local, and tribal governments in the aggregate, 
or by the private sector, of $100 million (adjusted annually for 
inflation) in any 1 year.'' FDA has determined that this proposed rule 
does not constitute a significant rule under the Unfunded Mandates 
Reform Act.
 
VII. Paperwork Reduction Act
 
    FDA tentatively concludes that this proposed rule contains no 
collections of information. Therefore, clearance by the OMB under the 
Paperwork Reduction Act of 1995 is not required.
 
VIII. Comments
 
    Interested persons may submit to the Dockets Management Branch 
(address above) written comments regarding this proposal on or before 
June 11, 2001. Two copies of any comments are to be submitted, except 
that individuals may submit one copy. Comments are to be identified 
with the docket number found in brackets in the heading of this
 
[[Page 16891]]
 
document. Received comments may be seen in the office above between 9 
a.m. and 4 p.m., Monday through Friday.
 
IX. Effective Date
 
    The agency intends to make any final rule based on this proposal 
effective January 1, 2002. The agency will publish a confirmation 
notice for a final rule in the Federal Register no later than 180 days 
before the effective date. The agency is providing 180 days before the 
effective date to permit affected firms adequate time to take 
appropriate steps to bring their product into compliance with the 
standard imposed by the new rule.
 
X. References
 
    1. U.S. EPA, Regulatory Impact Analysis of Final Disinfectant/
Disinfection By-Products Regulations, Washington, DC, app. E, pp. E-
4 and E-5, EPA 815-B-98-002. PB 99-111304, 1998.
    2. Memorandum from Dominic Mancini to the record, March 13, 
2001.
 
List of Subjects
 
21 CFR Part 129
 
    Beverages,  Bottled   water , Food packaging, Reporting and 
recordkeeping requirements.
 
21 CFR part 165
 
    Beverages,  Bottled   water , Food grades and standards, Incorporation 
by reference.
 
    Therefore, under the Federal Food, Drug, and Cosmetic Act and under 
authority delegated to the Commissioner of Food and Drugs, it is 
proposed that 21 CFR parts 129 and 165 be amended as follows:
 
PART 129--PROCESSING AND BOTTLING OF  BOTTLED  DRINKING  WATER 
 
    1. The authority citation for 21 CFR part 129 continues to read as 
follows:
 
    Authority: 21 U.S.C. 342, 348, 371, 374; 42 U.S.C. 264.
    2. Section 129.35 is amended by redesignating paragraph (a)(4)(iii) 
as paragraph (a)(4)(iv) and by adding new paragraph (a)(4)(iii) to read 
as follows:
 
 
Sec. 129.35  Sanitary facilities.
 
* * * * *
    (a)    *    *    *
    (4)    *    *    *
    (iii) Firms that do not use a public  water  system as the source of 
their  water  and whose source  water  has not been treated with a 
chlorine-based disinfectant or ozone do not have to test their source 
 water  for the residual disinfectants and DBP's listed in 
Sec. 165.110(b)(4)(iii)(H) of this chapter. Firms that do not use a 
public  water  system as the source of their  water  but whose source  water  
has been treated with a chlorine-based disinfectant or ozone must test 
their source  water  for the residual disinfectants and the DBP's listed 
in Sec. 165.110(b)(4)(iii)(H) that are likely to result from such 
treatment.
* * * * *
 
PART 165--BEVERAGES
 
    1. The authority citation for 21 CFR part 165 continues to read as 
follows:
 
    Authority: 21 U.S.C. 321, 341, 343, 343-l, 348, 349, 371, 379e.
    2. Section 165.110 is amended by revising paragraph (b)(1)(ii); by 
adding paragraphs (b)(1)(iii), (b)(4)(iii)(H), and (b)(4)(iii)(I); and 
in the table in paragraph (b)(4)(i)(A) by removing the entry for 
``Organics: Total Trihalomethanes'' to read as follows:
 
 
Sec. 165.110   Bottled   water .
 
* * * * *
    (b)    *    *    *
    (1)    *    *    *
    (ii) Total trihalomethanes (TTHM) means the sum of the 
concentration in milligrams per liter of the trihalomethane compounds 
(trichloromethane, dibromochloromethane, bromodichloromethane, and 
tribromomethane), rounded to three significant figures.
    (iii) Haloacetic acids (five) (HAA5) means the sum of the 
concentrations in milligrams per liter of the haloacetic acid compounds 
(monochloroacetic acid, dichloroacetic acid, trichloroacetic acid, 
monobromoacetic acid, and dibromoacetic acid), rounded to two 
significant figures after addition.
    (4)    *    *    *
    (iii)    *    *    *
    (H) The allowable levels for residual disinfectants and 
disinfection byproducts are as follows:
 
------------------------------------------------------------------------
                                            Concentration in milligrams
                Substance                            per liter
------------------------------------------------------------------------
Disinfection byproducts
  Bromate................................  0.010
  Chlorite...............................  1.0
  Haloacetic acids (five) (HAA5).........  0.060
  Total Trihalomethanes (TTHM)...........  0.080
Residual disinfectants
  Chloramine.............................  4.0 (as Cl2)
  Chlorine...............................  4.0 (as Cl2)
  Chlorine dioxide.......................  0.8 (as ClO2)
------------------------------------------------------------------------
 
    (I) Analysis to determine compliance with the requirements of 
paragraph (b)(4)(iii)(H) of this section shall be conducted in 
accordance with an applicable method listed in paragraphs 
(b)(4)(iii)(I)(1) through (b)(4)(iii)(I)(7) of this section and 
described in ``Method 300.1, Determination of Inorganic Anions in 
Drinking  Water  by Ion Chromatography,'' Rev. 1.0, U.S. EPA, 1997, EPA/
600/R-98/118; ``Methods for the Determination of Inorganic Substances 
in Environmental Samples,'' U.S. EPA, August 1993, EPA/600/R-93/100; 
``Methods for the Determination of Organic Compounds in Drinking  Water -
Supplement II,'' U.S. EPA, August 1992, EPA/600/R-92/129; ``Methods for 
the Determination of Organic Compounds in Drinking  Water -Supplement 
III,'' U.S. EPA, August 1995, EPA/600/R-95/131; ``Standard Methods for 
the Examination of  Water  and Wastewater,'' 19th Ed., American Public 
Health Association, 1995; and ``Annual Book of ASTM Standards,'' vol. 
11.01, American Society for Testing and Materials, 1996, which are 
incorporated by reference in accordance with 5 U.S.C. 552(a) and 1 CFR 
part 51. Copies of the following publications are available from the 
National Technical Information Service (NTIS): EPA/600/R-95/131 (NTIS 
number PB95-261616), EPA/600/R-92/129 (NTIS number PB92-207703), EPA/
600/R-93/100 (NTIS number PB94-121811), and EPA/600/R-98/118 (NTIS 
number PB98-169196). NTIS can be contacted at NTIS, U.S. Department of 
Commerce, 5285 Port Royal Rd., Springfield, VA 22161, 1-800-553-6847 or 
703-605-6000, www.ntis.gov. Copies of the publication EPA/600/R-98/118 
are also available from the Chemical Exposure Research Branch, 
Microbiological and Chemical Exposure Assessment Research Division, 
National Exposure Research Laboratory, U.S. EPA, Cincinnati, OH 45268, 
513-569-7757, (FAX) 513-569-7757. Copies of ``Standard Methods for the 
Examination of  Water  and Wastewater,'' 19th Ed., are available from the 
American Public Health Association, 1015 15th Street, NW., Washington, 
DC 20005. All of the publications cited in paragraph (b)(4)(iii)(I) of 
this section may be examined at the Office of the Federal Register, 800 
North Capitol St. NW., suite 700, Washington, DC, or at the Center for 
Food Safety and Applied Nutrition's Library, 200 C St. SW., Washington, 
DC 20204. Copies of ``Annual Book of ASTM Standards,'' 1996, vol. 
11.01, are available from the American Society for Testing and 
Materials, 100 Barr Harbor Dr., West Conshohoken, PA 19428, or may be 
examined at the Office of the Federal Register. Copies of the methods 
incorporated by reference in paragraph (b)(4)(iii)(I) of this section 
may also be examined at the Center for Food Safety
 
[[Page 16892]]
 
and Applied Nutrition's Library, 200 C St. SW., Washington DC 20204.
    (1) Bromate shall be measured using the following method: Method 
300.1--``Determination of Inorganic Anions in Drinking  Water  by Ion 
Chromatography,'' Rev. 1.0, U.S. EPA, 1997, EPA/600/R-98/118, which is 
incorporated by reference in accordance with 5 U.S.C. 552(a) and 1 CFR 
part 51. The availability of this incorporation by reference is given 
in paragraph (b)(4)(iii)(I) of this section.
    (2) Chlorite shall be measured using the following methods:
    (i) Method 300.0--``Determination of Inorganic Anions by Ion 
Chromatography,'' Rev. 2.1. The revision is contained in the manual 
entitled ``Methods for the Determination of Inorganic Substances in 
Environmental Samples,'' U.S. EPA, August 1993, EPA/600/R-93/100, which 
is incorporated by reference in accordance with 5 U.S.C. 552(a) and 1 
CFR part 51. The availability of this incorporation by reference is 
given in paragraph (b)(4)(iii)(I) of this section.
    (ii) Method 300.1--``Determination of Inorganic Anions in Drinking 
 Water  by Ion Chromatography,'' Rev. 1.0, U.S. EPA, 1997, EPA/600/R-98/
118, which is incorporated by reference in accordance with 5 U.S.C. 
552(a) and 1 CFR part 51. The availability of this incorporation by 
reference is given in paragraph (b)(4)(iii)(I) of this section.
    (3) HAA5 shall be measured using the following methods:
    (i) Method 552.1--``Determination of Haloacetic Acids and Dalapon 
in Drinking  Water  by Ion Exchange Liquid-Solid Extraction and Gas 
Chromatography with Electron Capture Detection,'' Rev. 1.0. The 
revision is contained in the manual entitled ``Methods for the 
Determination of Organic Compounds in Drinking  Water -Supplement II,'' 
U.S. EPA, August 1992, EPA/600/R-92/129, which is incorporated by 
reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The 
availability of this incorporation by reference is given in paragraph 
(b)(4)(iii)(I) of this section.
    (ii) Method 552.2--``Determination of Haloacetic Acids and Dalapon 
in Drinking  Water  by Liquid-Liquid Extraction, Derivatization and Gas 
Chromatography with Electron Capture Detection,'' Rev. 1.0. The 
revision is contained in the manual entitled ``Methods for the 
Determination of Organic Compounds in Drinking  Water -Supplement III,'' 
U.S. EPA, August 1993, EPA/600/R-95/131, which is incorporated by 
reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The 
availability of this incorporation by reference is given in paragraph 
(b)(4)(iii)(I) of this section.
    (iii) Method 6251 B--``Disinfection By-Products: Haloacetic Acids 
and Trichlorophenol,'' which is contained in the book entitled 
``Standard Methods for the Examination of  Water  and Wastewater,'' 19th 
Ed., which is incorporated by reference in accordance with 5 U.S.C. 
552(a) and 1 CFR part 51. The availability of this incorporation by 
reference is given in paragraph (b)(4)(iii)(I) of this section.
    (4) TTHM shall be measured using the following methods:
    (i) Method 502.2--``Volatile Organic Compounds in  Water  by Purge 
and Trap Capillary Column Gas Chromatography with Photoionization and 
Electrolytic Conductivity Detectors in Series,'' Rev. 2.1. The revision 
is contained in the manual entitled ``Methods for the Determination of 
Organic Compounds in Drinking  Water -Supplement III,'' U.S. EPA, August 
1993, EPA/600/R-95/131, which is incorporated by reference in 
accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The availability of 
this incorporation by reference is given in paragraph (b)(4)(iii)(I) of 
this section.
    (ii) Method 524.2--``Measurement of Purgeable Organic Compounds in 
 Water  by Capillary Column Gas Chromatography/Mass Spectrometry,'' Rev. 
1.0. The revision is contained in the manual entitled ``Methods for the 
Determination of Organic Compounds in Drinking  Water -Supplement III,'' 
U.S. EPA, August 1993, EPA/600/R-95/131, which is incorporated by 
reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The 
availability of this incorporation by reference is given in paragraph 
(b)(4)(iii)(I) of this section.
    (iii) Method 551.1--``Determination of Chlorination Disinfection 
Byproducts, Chlorinated Solvents, and Halogenated Pesticides/Herbicides 
in Drinking  Water  by Liquid-Liquid Extraction and Gas Chromatography 
with Electron-Capture Detection,'' Rev. 1.0. The revision is contained 
in the manual entitled ``Methods for the Determination of Organic 
Compounds in Drinking  Water -Supplement III,'' U.S. EPA, August 1993, 
EPA/600/R-95/131, which is incorporated by reference in accordance with 
5 U.S.C. 552(a) and 1 CFR part 51. The availability of this 
incorporation by reference is given in paragraph (b)(4)(iii)(I) of this 
section.
    (5) Compliance with the chloramine standard can be determined by 
measuring combined or total chlorine. The following methods shall be 
used to measure chloramine:
    (i) ASTM Method D1253-86--`` Standard Test Method for Residual 
Chlorine in  Water ,'' which is contained in the book entitled ``Annual 
Book of ASTM Standards,'' 1996, vol. 11.01, which is incorporated by 
reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The 
availability of this incorporation by reference is given in paragraph 
(b)(4)(iii)(I) of this section.
    (ii) Method 4500-Cl D--``Amperometric Titration Method,'' which is 
contained in the book entitled ``Standard Methods for the Examination 
of  Water  and Wastewater,'' 19th Ed., which is incorporated by reference 
in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The availability 
of this incorporation by reference is given in paragraph (b)(4)(iii)(I) 
of this section.
    (iii) Method 4500-Cl F--``DPD Ferrous Titrimetric Method,'' which 
is contained in the book entitled ``Standard Methods for the 
Examination of  Water  and Wastewater,'' 19th Ed., which is incorporated 
by reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The 
availability of this incorporation by reference is given in paragraph 
(b)(4)(iii)(I) of this section.
    (iv) Method 4500-Cl G--``DPD Colorimetric Method,'' which is 
contained in the book entitled ``Standard Methods for the Examination 
of  Water  and Wastewater,'' 19th Ed., which is incorporated by reference 
in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The availability 
of this incorporation by reference is given in paragraph (b)(4)(iii)(I) 
of this section.
    (v) Method 4500-Cl E--``Low-Level Amperometric Titration Method,'' 
which is contained in the book entitled ``Standard Methods for the 
Examination of  Water  and Wastewater,'' 19th Ed., which is incorporated 
by reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The 
availability of this incorporation by reference is given in paragraph 
(b)(4)(iii)(I) of this section.
    (vi) Method 4500-Cl I--``Iodometric Electrode Technique,'' which is 
contained in the book entitled ``Standard Methods for the Examination 
of  Water  and Wastewater,'' 19th Ed., which is incorporated by reference 
in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The availability 
of this incorporation by reference is given in paragraph (b)(4)(iii)(I) 
of this section.
    (6) Compliance with the chlorine standard can be determined by 
measuring free or total chlorine. The following methods shall be used 
to measure chlorine:
    (i) ASTM Method D1253-86--``Standard Test Method for Residual 
Chlorine in  Water ,'' which is contained in the book entitled ``Annual 
Book of ASTM Standards,'' 1996, vol. 11.01, which is incorporated by 
reference in accordance with 5 U.S.C. 552(a) and 1
 
[[Page 16893]]
 
CFR part 51. The availability of this incorporation by reference is 
given in paragraph (b)(4)(iii)(I) of this section.
    (ii) Method 4500-Cl D--``Amperometric Titration Method,'' which is 
contained in the book entitled ``Standard Methods for the Examination 
of  Water  and Wastewater,'' 19th Ed., which is incorporated by reference 
in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The availability 
of this incorporation by reference is given in paragraph (b)(4)(iii)(I) 
of this section.
    (iii) Method 4500-Cl F--``DPD Ferrous Titrimetric Method,'' which 
is contained in the book entitled ``Standard Methods for the 
Examination of  Water  and Wastewater,'' 19th Ed., which is incorporated 
by reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The 
availability of this incorporation by reference is given in paragraph 
(b)(4)(iii)(I) of this section.
    (iv) Method 4500-Cl G--``DPD Colorimetric Method,'' which is 
contained in the book entitled ``Standard Methods for the Examination 
of  Water  and Wastewater,'' 19th Ed., which is incorporated by reference 
in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The availability 
of this incorporation by reference is given in paragraph (b)(4)(iii)(I) 
of this section.
    (v) Method 4500-Cl E--``Low-Level Amperometric Titration Method,'' 
which is contained in the book entitled ``Standard Methods for the 
Examination of  Water  and Wastewater,'' 19th Ed., which is incorporated 
by reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The 
availability of this incorporation by reference is given in paragraph 
(b)(4)(iii)(I) of this section.
    (vi) Method 4500-Cl I--``Iodometric Electrode Technique,'' which is 
contained in the book entitled ``Standard Methods for the Examination 
of  Water  and Wastewater,'' 19th Ed., which is incorporated by reference 
in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The availability 
of this incorporation by reference is given in paragraph (b)(4)(iii)(I) 
of this section.
    (vii) Method 4500-Cl H--``Syringaldazine (FACTS) Method,'' which is 
contained in the book entitled ``Standard Methods for the Examination 
of  Water  and Wastewater,'' 19th Ed., which is incorporated by reference 
in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The availability 
of this incorporation by reference is given in paragraph (b)(4)(iii)(I) 
of this section.
    (7) Chlorine dioxide shall be measured using the following methods:
    (i) Method 4500-ClO2 D--``DPD Method,'' which is 
contained in the book entitled ``Standard Methods for the Examination 
of  Water  and Wastewater,'' 19th Ed., which is incorporated by reference 
in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The availability 
of this incorporation by reference is given in paragraph (b)(4)(iii)(I) 
of this section.
    (ii) Method 4500-ClO2 E--``Amperometric Method II,'' 
which is contained in the book entitled ``Standard Methods for the 
Examination of  Water  and Wastewater,'' 19th Ed., which is incorporated 
by reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. The 
availability of this incorporation by reference is given in paragraph 
(b)(4)(iii)(I) of this section.
* * * * *
 
    Dated: March 20, 2001.
Ann M. Witt,
Acting Associate Commissioner for Policy.
[FR Doc. 01-7562 Filed 3-23-01; 8:45 am]
BILLING CODE 4160-01-S
 


Foods Home   |   FDA Home   |   Search/Subject Index   |   Disclaimers & Privacy Policy